How to install Maven on Windows
Maven is a Java application, so we are just fine with expanding product zip package and setting environment variables M2_HOME and JAVA_HOME and set PATH.
Creating a Maven Project
Maven in 5 Minutes
Maven in 5 seconds… dothis:
mvn archetype:generate -DgroupId=com.mycompany.app -DartifactId=my-app -DarchetypeArtifactId=maven-archetype-quickstart -DinteractiveMode=false
MOM (Master Of Modules) manages synthesizer modules to make them work as a single musical instrument. The main responsibilities of MOM are
- Control patching.
- Control parameters.
- Organize voices.
- (possibly) Organize modules such as device ID management.
Designing and implementing MOM and synth module data model is yet another challenge out of building CAN network. Basically, the inter-module communication depends on CAN physical layer, but it’s a pain to dragging such a dependency during the MOM development. I’m sure the CAN network would be quite unstable at first and I don’t want to stop and troubleshoot CAN while I’m working on MOM.
So, in order to remove dependency on CAN network, I’ll build the initial version of MOM based on TCP/IP with dummy (stub) synth modules that are purely software oriented and talk TCP/IP. Once the MOM design is fixed, I can replace the TCP/IP driver by CAN driver later. It will not ruin the module data model.
As I mentioned in the previous article, I’ll use MCP2515 CAN controller for inter-module communication (initially, at least) for the Analog3 Project.
Datasheet of this device is available at the product page.
MCP2515 consists of CAN protocol engine, data buffers, controller, and SPI interface as illustrated in the picture below.
You need to attach a processor to make this device functional. In early phase of the project, I’m thinking of using a Raspberry Pi as the Master Of Modules (mom) and Arduino’s for dummy synthesizer modules. Arduino is not a realistic solution for Analog3 both in terms of cost and performance. So, I’m thinking of implementing a common synthesizer module driver based on PSoC or CAN enabled AVR. MCP2551 is CAN transceiver.
It may take a while to get used to MCP2515. Here are several links that are useful for getting started:
MCP2515 Linux Device Driver (probably for Raspberry Pi)
Arduino Example Sketch
AVR Example Code (C)
I’ve been trying for a year to make my own serial interface protocol to exchange data among synth modules. Though it showed some progress, I kind of giving up this approach. The problem is complexity of serial interface controller. A controller for multi-master serial interface is complex. Implementing using a generic device is more costly in many sense than I expected. I started with Arduino. This was the easiest approach but channel was too slow. I could only achieve 50kbps. Then I tried implementing it into AVR using assembler language. It went 100kbps but it was about the limit. The most serious problem with MPU was that the processing is always on single thread. Some data processing has to be done in parallel during data reception, but it was pretty inefficient to run such concurrent tasks on 8-bit simple processor. Overhead for such multi-tasking killed the speed. Then, I moved onto PSoC. It achieves bit rate 400kbps easily and it might go higher if it’s tuned well. However, the logic to handle collision is so complex that I eventually am suffered from lack of resources in PSoC.
So at this point, it seems more practical to use a ready-made implementation of an existing protocol, which is CAN.
The reason I didn’t go for CAN at first was speed. I wanted to use the interface even for synching oscillators. I was not sure if 44bit-at-shortest message from at 1 Mbps is short enough for that usage. (I’m not sure yet. It’s about 22kHz rate if you keep repeating shortest CAN message at the highest rate. That’s pretty close to audio frequency. If an oscillator keeps sending such messages, the communication channel would be pretty much occupied.) So probably I need to give up some usage of the common data bus. I will go with following approach:
- Use cheap CAN controller and transceiver: MCP2515 and MCP2551.
- MCP2515 is controlled by SPI. Most processors can use it.
- I’ll use Raspberry Pi for the master synth controller module.
- Synth modules can be based on PSoC or AVR. These two are ones I am familiar with.
- I’ll give up some features such as oscillator sync network.
Search engine helps, but I’m so lazy that I don’t like to do the same search repeatedly.
Wireless LAN setup:
Use application “Wifi Configuration” from GUI menu.
Common WIFI dongle problem of falling of network:
Power management feature is enabled in default for device 8192cu. Having following file resolves the issue:
pi@raspberrypi ~ $ cat /etc/modprobe.d/8192cu.conf
# prevent power down of wireless when idle
options 8192cu rtw_power_mgnt=0 rtw_enusbss=0
Set static address to wifi interface:
Edit /etc/network/interfaces. If the setup for wlan looks like following,
iface wlan0 inet manual
iface default inet dhcp
modify as follows:
iface wlan0 inet manual
iface default inet static
Install Inconsolata font:
% sudo dpkg-reconfigure tzdata
Raspberry Pi B+ Pinout
Picture in Pi4J Project:
The I2C slave that I’m developing has been failing intermittently. I finally noticed this was a known bug in Raspberry Pi that mishandles clock stretching.
I2C slave may delay response by holding SCL low. However, when the slave does it, the I2C master in Raspberry Pi gives very short clock for the first bit of the next byte. The symptom can be seen as following picture.
More detail explanation can be read in this link:
In order to workaround this, I set data rate in I2C slave module higher. The communication rate is 400 kbps, but I set the data rate 1000 kbps. It worked for me. Here is the setup of I2C slave module.