Posted intech notes

DC-DC Booster Design using MC34063

DR-110 that I am modifying currently takes 6V power supply from 4 AA batteries or 9V from an AC adapter. But since I'm thinking of connecting to USB, it's convenient if we can draw power from it. From the device circuit diagram, I found the device requires at least 6V supply although USB supply power is 5V. It's a good opportunity to learn how to use DC-DC booster since more project that uses USB will come. I live near Jameco. It's the best to use one they carry. It's even better if the package is DIP since I often use breadboards. I checked their catalog and found a switching regulator…
Posted inMod

DR-110 Driving Pulses

The schematic of DR-110 is: For this circuit, each percussion element seems to sound when you put a negative pulse of width 1 ms. I've put oscilloscope to observe the pulses come as expected. Here are the pulses to the bass drum and output: Blue: Input pulse, Red: Output Blue: Input pulse, Red: Output The pulse width looks to be around 1.3 ms. These are the pulses to the snare drum and output: Blue: Input pulse: Red: Output Blue: Input pulse, Red: Output For the hand clap, I only took pulses: Blue: CP I, Red: CP II This is a simulated output of the bass drum circuit: The output would…
Posted inMod

Started Modifying DR-110

It's been a while since I stopped building things. But it's a new year, I'll try restarting it. For not making things for long, I cannot do anything aggressive yet. I would start with picking up an old DR-110 from my toy box to modify it. This device is half-dead. Upper half of the display is not functioning. Membrane switches are not working well, too. The case is nice looking, so it may be fun to keep it and make it work. But it's an old device and what can be done is pretty limited compared to contemporary feature rich devices. I would go simply with replacing the control by…
Posted inRaspberry Pi tech notes

Building DPDK on Raspberry Pi 3

I'm trying to build DPDK on Raspberry Pi 3 but couldn't do it on Raspbian since it's a 32-bit OS. DPDK uses several assembler instructions for ARM 8 that are only valid on 64-bit OS. So my effort starts with installing a 64-bit OS. I found SUSE has released 64-bit Linux for Raspberry Pi 3:https://en.opensuse.org/HCL:Raspberry_Pi3 I started with this OS image. Choosing the Image Three versions of distributions are avalable for Raspberry Pi 3: openSUSE Leap openSUSE Tumbleweed non-upstream openSUSE Tumbleweed I tried openSUSE Leap first, but could not zypper update. Then I tried openSUSE Tumbleweed. This worked fine. There are four variations of images: JeOS image (Just Enough OS)…
Posted inanalog2.0

Improvement of Analog2.0 LFO

The schematic above represents the latest Analog2.0 LFO circuit. This circuit has a long-existing problem. The oscillation affects the power supply and that causes instability in VCO pitch; You would hear the VCO pitch shifting along with the LFO’s oscillation. I’ve tried eliminating this problem.

Posted inanalog3 BeagleBone CAN

BeagleBone Green: Enable CAN on Startup

Three steps: Enable CAN overlay by configuring cape manager Configure network interface Install startup program 1. Enable CAN overlay Add following line in /etc/default/capemgr CAPE=BB-DCAN1 2. Configure network interface Add following lines in /etc/network/interfaces auto can0 iface can0 inet manual pre-up /sbin/ip link set $IFACE type can bitrate 1000000 listen-only off up /sbin/ifconfig $IFACE up down /sbin/ifconfig $IFACE down 3. Install startup program Setting the CAN interface to /etc/network/interface does not enable the CAN interface on startup for some reason. In order to workaround this problem, I installed a startup program as follows. Following link was helpful: Running a script on Beaglebone Black boot/ startup The startup script to run…
Posted inanalog3 BeagleBone

BeagleBoneGreen: Disabling Wi-Fi Power Management Permanently

The operating system is Debian. This is a dirty solution but it does work anyway. root@beaglebone:~# cat /etc/pm/power.d/wlan0_pm_off #!/bin/bash [ -x /sbin/iwconfig ] || exit 0 [ -n "`/sbin/iwconfig 2>/dev/null | grep wlan0`" ] || exit 0 /sbin/iwconfig wlan0 power off root@beaglebone:~# crontab -l | grep -v "^#" */1 * * * * /etc/pm/power.d/wlan0_pm_off root@beaglebone:~# iwconfig wlan0 wlan0 IEEE 802.11abgn ESSID:"*****" ... Power Management:off ...
Posted inanalog3 BeagleBone CAN

Test CAN connection between BeagleBone and MIDI/CAN converter

1. Enabled CAN at 1Mbps on BeagleBone: Following operations seem to be necessary every BeagleBone boot. TBD to setup auto configuration on startup. root@beaglebone:~# echo BB-DCAN1 > /sys/devices/platform/bone_capemgr/slots root@beaglebone:~# ip link set can0 up type can bitrate 500000 root@beaglebone:~# ip link set can0 up type can bitrate 1000000 root@beaglebone:~# ifconfig can0 can0      Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00             UP RUNNING NOARP  MTU:16  Metric:1           RX packets:2 errors:0 dropped:2 overruns:0 frame:0           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0           collisions:0 txqueuelen:10            RX bytes:16 (16.0 B)  TX bytes:0 (0.0…
Posted inanalog3 BeagleBone CAN

Enable CAN on the BeagleBone Green

I've tried to enable CAN on my BeagleBone Green board. I had to stop the work before verification, because my logic analyzer is unavailable now. I record what I did in this article to make things reproducible when the logic analyzer is back. There are several helpful links: http://www.embedded-things.com/bbb/enable-canbus-on-the-beaglebone-black/ http://electronics.stackexchange.com/questions/195416/beaglebone-black-can-bus-setup https://groups.google.com/forum/embed/?place=forum/beagleboard&showsearch=true&showpopout=true&showtabs=false&hideforumtitle=true&parenturl=http%3A%2F%2Fbeagleboard.org%2Fdiscuss%23bone_forum_embed#!category-topic/beagleboard/can/SjWwVngIPh8 Readings to understand device tree overlay: Device Tree for Dummies: http://events.linuxfoundation.jp/sites/events/files/slides/petazzoni-device-tree-dummies.pdf Device Tree Overlays (in adafruit) https://learn.adafruit.com/introduction-to-the-beaglebone-black-device-tree/device-tree-overlays Here are what I did: # make a workspace root@beaglebone:~# mkdir can root@beaglebone:~# cd can root@beaglebone:~/can# pwd /root/can # check if CAN is enabled ... no root@beaglebone:~/can# dmesg | grep can # take backup of the original device tree blob file for…